Resistor 49.9 ohm
Electronics • Resistor

Electronics • Resistor

Available Quantity : 600
Package : 1206

50 ohm 49.9 ohm

LED RGB CLEAR 4PLCC SMD
Electronics • LED

Red, Green, Blue (RGB) 621nm Red, 528nm Green, 470nm Blue LED Indication - Discrete 2.1V Red, 3.2V Green, 3.2V Blue 4-SMD, J-Lead

Available Quantity : 227
Package : PLCC4

PLCC4 RGB LED

CONN HDR 2POS 0.1 TIN SMD
Electronics • Pins & Connector

2 Position Header, Top or Bottom Entry Connector 0.100" (2.54mm) Surface Mount Tin https://www.digikey.in/en/products/detail/sullins-connector-solutions/NPTC021KFXC-RC/776052

Available Quantity : 50
Package : 2.54mm

vertical SMD 1x02

MPU-6050 3-Axis Accelerometer and Gyro Sensor
Electronics • Sensors

The MPU6050 devices combine a 3-axis gyroscope and a 3-axis accelerometer on the same silicon together with an onboard Digital Motion Processor (DMP) capable of processing complex 9-axis MotionFusion algorithms.

Available Quantity : 4
Package :

IMU Magnetometer & Gyroscope Accelerometer

N20 3V 150RPM Micro Metal Gear DC Motor With Encoder
Electro-Mechanics • Motor

These N20 3V 150RPM Micro Metal Gear DC Motor With Encoder is intended for use at 3V. Though in general, these kinds of motors can run at voltages above and below this nominal voltage; so they should comfortably operate till the 3V (rotation can start at voltages as low as 0.5 V). Lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor. The micro metal gear motors are available in a wide range of gear ratios—from 5:1 up to 1000:1. With the exception of 1000:1 gear ratio versions, all of the micro metal gear motors have the same physical dimensions; so one version can be easily swapped for another if your design requirements change.

Available Quantity : 4
Package :

encoder motor

300 RPM BO Motor-Straight
Electro-Mechanics • Motor

This is a 300 RPM BO Motor-Straight. Small shaft with matching wheels gives an optimized design for your application or robot. Mounting holes on the body & light weight makes it suitable for in-circuit placement. This motor can be used with 69mm Diameter Wheel for Plastic Gear Motors and 87mm Diameter Multipurpose Wheel for Plastic Gear Motors.

Available Quantity : 20
Package :

motor

WS2812B Mini RGB SMD LED – SMD3535 – 4 pin
Electronics • Sensors

WS2812B Mini RGB SMD LED is an intelligent control LED light source that the control circuit and RGB chip integrated in a package of 3535 component. Its’ internals include intelligent digital port data latch and signal reshaping amplification drive circuit. It also includes a high-precision internal oscillator and a programmable constant current control part to ensure high color consistency. The data transfer protocol use single NZR communication mode. After the pixel power-on reset, the DIN port receive data from controller, the first pixel collect initial 24bit data then sent to the internal data latch, the other data which reshaping by the internal signal reshaping amplification circuit sent to the next cascade pixel through the DO port. After transmission for each pixel, the signal reduces by 24bit. The pixels adopt auto reshaping transmit technology, making the pixel cascade number not limited to the signal transmission, and only makes it dependent on the speed. https://www.ktron.in/product/ws2812b-mini-smd-3535-4-pin/

Available Quantity : 174
Package : SMD3535

smd LED neopixel led Addressable LED neopixel

WS2812B RGB Smd 5050 Led
Electronics • LED

WS2812B RGB Smd 5050 Led is a intelligent control LED light source that the control circuit and RGB chip are integrated in a package of 5050 components. It internal include intelligent digital port data latch and signal reshaping amplification drive circuit. Also include a precision internal oscillator and a 12V voltage programmable constant current control part, effectively ensuring the pixel point light color height consistent. https://www.ktron.in/product/ws2812b-rgb-smd-5050-led/

Available Quantity : 183
Package : 5050

smd LED neopixel led Addressable LED 5050 Addressable

Uno Arduino Development Board
Electronics • Dev board

The Uno R3 CH340G ATmega328p Development Board is the low-cost version of the popular Uno R3 Arduino. It is assembled with the CH340 USB to Serial converter chip, instead of using an Atmega16U2 chip. We have used plenty of these low-cost Arduino boards with CH340 chips, and have found them to work perfectly. The only time the CH340 chip is used is during programming and when using the serial output of the USB port. During normal operation, this board is identical to the more expensive version without CH340 chip.

Available Quantity : 5
Package :

board Development

Triple Axis Accelerometer Module
Electronics • Sensors

This ADXL345 Triple axis accelerometer module is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16g. Digital output data is format as 16-bit twos complement and is accessible through either an SPI (3- or 4-wire) or I2C digital interface.

Available Quantity : 5
Package :

sensor module

INMP441 MEMS High Precision Omnidirectional Microphone Module
Electronics • Sensors

The INMP441 is a high-performance, low-power, digital output, omnidirectional MEMS microphone with a bottom port. The complete INMP441 solution consists of a MEMS sensor, signal conditioning, analog to digital converter, anti-aliasing filter, power management, and industry-standard 24-bit I2S interface. The I2S interface allows the INMP441 to be directly connected to digital processors such as DSPs and microcontrollers without the need for an audio codec for use in the system. The INMP441 has a high signal-to-noise ratio and is an excellent choice for near-field applications. The INMP441 has a flat wideband frequency response that results in a high definition of natural sound.

Available Quantity : 4
Package :

sensor module

Hall-Effect Magnetic Position Sensor
Electronics • Sensors

The MT8111ET - Hall-Effect Magnetic Position Sensor Unipolar 110Gs 3Pin SOT-23 (Thin) is produced by BCD technology with both high performance and high reliability. The Hall IC internally includes an on-chip Hall voltage generator, a voltage regulator for operation with supply voltage of 2.8V to 24V, a smallsignal amplifier, Hall sensors with dynamic offset cancellation, a schmitt trigger and an open-drain output with over-current protection. It features temperature compensation technique to make the magnetic switching points stable over a wide temperature range.

Available Quantity : 6
Package :

smd sensor

Pressure sensor
Electronics • Sensors

Pressure Sensor 5.37PSI (37kPa) Vented Gauge Male - 0.1" (2.59mm) Tube 0 mV ~ 31 mV 6-SMD Module

Available Quantity : 5
Package :

sensor module

DRV8825 Stepper Motor Driver with Aluminum Heat Sink
Electronics • Motor_Drivers

The DRV8825 Stepper Motor Driver with Aluminum Heat Sink is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of the A4988 stepper motor driver carriers, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent, and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling). Img 0849 Note: We are supplying two DRV8825 Drivers as DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Good Quality and DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Normal Quality. The difference between them is, the good quality DRV8825 has more number of PCB layers and it features the connecting pins which are of gold plated as compared to other. (refer to above image) Using the Driver Wiring Diagram For Drv8825 Stepper Motor Driver Features : Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45 V maximum supply voltage Built-in regulator (no external logic voltage supply needed) Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer, 2 oz copper PCB for improved heat dissipation Exposed solderable ground pad below the driver IC on the bottom of the PCB Package Includes : 1 x DRV8825 Stepper Motor Driver with Aluminum Heat Sink- Good Quality. https://robu.in/product/drv8825-stepper-motor-driver-aluminum-heat-sink-good-quality/

Available Quantity : 12
Package : soldered module

motor Driver Stepper Driver drv8825

MOSFET N-CH 30V 1.7A SOT-323
Electronics • Mosfets and Transistors

N-Channel 30 V 1.7A (Ta) 350mW (Ta) Surface Mount SC-70-3 https://www.digikey.in/en/products/detail/alpha-omega-semiconductor-inc/AO7400/1855856

Available Quantity : 82
Package : SC-70, SOT-323

N MOS N Channel MOSFET 1.7 A